我手里没有小九，所以一直没有测试这个包。听到吧友说刷不进去，然后我就去mt15i吧看了看（因为他们都是属于xperia系列，很多东西都差不多），他们成功了，刷机方法是用cm12.1的内核刷cm13的rom，然后再刷cm13的内核。这种方法我不知道吧友们有没有尝试。然后今天到xda论坛查了好多帖子，然后去了hithub（他们存放小酒的源码的地方），在wiki里面看到了他们的方法。下面详细内容。
wt19i吧 关注：2,127贴子：97,997
不感兴趣
开通SVIP免广告
2.分区
原文如下，附简要说明:
ALL DATA WILL BE LOST. Backup anything you need.（分区内存卡数据会全部清空）
Basically, you need a normal SD card; if you repartitioned for Lollipop, you must revert that.(如果你曾为可小九的5.x分过区，你必须复原它。我的理解是，这个分区要格式化然后新建)
You MUST have exactly 1 partition on the card. The recovery cannot change the partition layout.（你必须有这样一个分区，recovery是不会更改它的输出路径的）
The partition type must be "primary" and "not active".（分区属性必须是主分区）
speed matters, this will hold the /data partition. UHS-1 / Class 10 strongly recommended.Note that Class10 cards can still differ a lot; the orange Samsung EVO cards seem to be good for this use case.
See Tuning SD Card Speed（最好是选择UHS-1/C10，【注意】即使是C10也很难让系统跑的很流畅，三星的evo内存卡挺不错的（他们的推荐），后面是一个测试内存卡的工具）
on Windows, use MiniTool partition wizard and an SD card reader (easy). On Linux, use gparted, or see Partitioning the SD Card using ADB (not easy)（在不同平台的分区工具，windows上用minitool分区助手）
Note that sometimes Partition Wizard creates a small empty 2nd partition - this could cause problems.（【注意】一些分区助手在分区的时候会额外多分出一个很小的分区，这个会导致以后的刷机失败）
Once you have the 1 partition:（分区，删除原有分区）
format to F2FS; or keep unformatted (then it will be formatted to F2FS later; the same should work with FAT32, but not all fat variants like vfat/exfat have been tested)（格式化成F2FS格式；或者不格式（也就是删除原有分区后就不管它了），在稍后的刷机过程中它会自动被格式化成F2FS，同理FAT32也会这样(也就是你直接给内存卡分成一个至少2g的空间和剩下的，然后设置主分区，不用删除原有分区），其他格式的分区内有测试（内存卡默认格式是fat32））
alternative: format to ext4 (this is no longer standard and not recommended, but it may be faster for some cards)(出了上面的分区方法，你也可以分成ext4，这不再像刷5.x的时候分区必须是ext4，但是这种格式会让一些内训卡的速度变快)
原文如下，附简要说明:
ALL DATA WILL BE LOST. Backup anything you need.（分区内存卡数据会全部清空）
Basically, you need a normal SD card; if you repartitioned for Lollipop, you must revert that.(如果你曾为可小九的5.x分过区，你必须复原它。我的理解是，这个分区要格式化然后新建)
You MUST have exactly 1 partition on the card. The recovery cannot change the partition layout.（你必须有这样一个分区，recovery是不会更改它的输出路径的）
The partition type must be "primary" and "not active".（分区属性必须是主分区）
speed matters, this will hold the /data partition. UHS-1 / Class 10 strongly recommended.Note that Class10 cards can still differ a lot; the orange Samsung EVO cards seem to be good for this use case.
See Tuning SD Card Speed（最好是选择UHS-1/C10，【注意】即使是C10也很难让系统跑的很流畅，三星的evo内存卡挺不错的（他们的推荐），后面是一个测试内存卡的工具）
on Windows, use MiniTool partition wizard and an SD card reader (easy). On Linux, use gparted, or see Partitioning the SD Card using ADB (not easy)（在不同平台的分区工具，windows上用minitool分区助手）
Note that sometimes Partition Wizard creates a small empty 2nd partition - this could cause problems.（【注意】一些分区助手在分区的时候会额外多分出一个很小的分区，这个会导致以后的刷机失败）
Once you have the 1 partition:（分区，删除原有分区）
format to F2FS; or keep unformatted (then it will be formatted to F2FS later; the same should work with FAT32, but not all fat variants like vfat/exfat have been tested)（格式化成F2FS格式；或者不格式（也就是删除原有分区后就不管它了），在稍后的刷机过程中它会自动被格式化成F2FS，同理FAT32也会这样(也就是你直接给内存卡分成一个至少2g的空间和剩下的，然后设置主分区，不用删除原有分区），其他格式的分区内有测试（内存卡默认格式是fat32））
alternative: format to ext4 (this is no longer standard and not recommended, but it may be faster for some cards)(出了上面的分区方法，你也可以分成ext4，这不再像刷5.x的时候分区必须是ext4，但是这种格式会让一些内训卡的速度变快)
4，清理内存卡（也就是3清之类的）
Boot to Recovery（进recovery）
factory reset > full factory reset（选择清除-恢复出厂）
Wipe cache（清理cach）
advanced > wipe system partition（高级，清理系统分区，也就是咱们的分的那个区）
NOTE: this will format the card to F2FS if necessary, and create /data and/data/media on it.（【注意】这会格式化那个分区成F2FS，如果必要的话还会创建/data和/data/media目录。ps咱们如果在分区的时候手动建立了新的分区比如ext4或者F2FS的话，这一步就跳过了）
/data/media is used to emulate an SD card (Android acts like its content is on a separate SD card, where photos are stored for example). You cannot access /data/media via the plain file system with a card reader.（原理巴拉巴拉……）
Boot to Recovery（进recovery）
factory reset > full factory reset（选择清除-恢复出厂）
Wipe cache（清理cach）
advanced > wipe system partition（高级，清理系统分区，也就是咱们的分的那个区）
NOTE: this will format the card to F2FS if necessary, and create /data and/data/media on it.（【注意】这会格式化那个分区成F2FS，如果必要的话还会创建/data和/data/media目录。ps咱们如果在分区的时候手动建立了新的分区比如ext4或者F2FS的话，这一步就跳过了）
/data/media is used to emulate an SD card (Android acts like its content is on a separate SD card, where photos are stored for example). You cannot access /data/media via the plain file system with a card reader.（原理巴拉巴拉……）
5重点来了：Flash the images using sideload（通过sideload刷入rom）
NOTE: You must have the latest ADB version 1.0.32. Check with 'adb version'.
With an older version you will get "protocol fault (no status)"（【注意】你的ADB版本必须是1.0.32以上，不然会报各种各样的错）
reboot again to recovery (Note: the "reboot recovery" option does not work. Do a normal reboot and press the recovery key instead)（重启到recovery）
connect USB to PC（连接PC）
Select Apply update > Apply from ADB（选择升级-从ADB升级）
Sideload LX13 rom (takes 10 minutes). Example:（升级，大概需要10分钟。代码如下）
adb sideload cm-13.0-20160224-UNOFFICIAL-LegacyXperia-urushi.zip
again, Select Apply update > Apply from ADB（再次选择升级-从ADB升级）
Sideload GAPPS (this is optional, but you most likely want it)（刷入GAOOPS，用不到的就不用刷了）
Sideload anything else you want (keyboard etc.)（还可以刷入其他你想的，比如刷入法软件等等）
NOTE: cm13 includes toybox instead of busybox (a tool to execute scripts). As a result, assume that images for older cm versions will not work.（cm13引入了toybox来代替busybox（这东西大家应该熟悉吧
），带来的结果是老版的cm固件在cm13上不工作（我不明白什么意思，所以就这么翻译了……
））
NOTE: install GAPPS before you boot for the first time. (Only before the first boot, installers get special privileges).（切记，如果要刷入GAPPS,要在刷rom的时候一同刷入，不然安装器没有特权安装，也就是可能安装不成功）
NOTE: if you have installed LX13 before, and you enabled ADB debugging and verified your PC, you can also move the images to the phone using ADB, and flash the images from the Recovery. It's easier to just use sideload.（这个不翻译了
）
NOTE: You must have the latest ADB version 1.0.32. Check with 'adb version'.
With an older version you will get "protocol fault (no status)"（【注意】你的ADB版本必须是1.0.32以上，不然会报各种各样的错）
reboot again to recovery (Note: the "reboot recovery" option does not work. Do a normal reboot and press the recovery key instead)（重启到recovery）
connect USB to PC（连接PC）
Select Apply update > Apply from ADB（选择升级-从ADB升级）
Sideload LX13 rom (takes 10 minutes). Example:（升级，大概需要10分钟。代码如下）
adb sideload cm-13.0-20160224-UNOFFICIAL-LegacyXperia-urushi.zip
again, Select Apply update > Apply from ADB（再次选择升级-从ADB升级）
Sideload GAPPS (this is optional, but you most likely want it)（刷入GAOOPS，用不到的就不用刷了）
Sideload anything else you want (keyboard etc.)（还可以刷入其他你想的，比如刷入法软件等等）
NOTE: cm13 includes toybox instead of busybox (a tool to execute scripts). As a result, assume that images for older cm versions will not work.（cm13引入了toybox来代替busybox（这东西大家应该熟悉吧
），带来的结果是老版的cm固件在cm13上不工作（我不明白什么意思，所以就这么翻译了……））NOTE: install GAPPS before you boot for the first time. (Only before the first boot, installers get special privileges).（切记，如果要刷入GAPPS,要在刷rom的时候一同刷入，不然安装器没有特权安装，也就是可能安装不成功）
NOTE: if you have installed LX13 before, and you enabled ADB debugging and verified your PC, you can also move the images to the phone using ADB, and flash the images from the Recovery. It's easier to just use sideload.（这个不翻译了
）
棉花糖 
吧 7.适配者的一些笔记
In Recovery mode, initially any adb command other than sideload results in "unauthorized". Once you have booted and authorized the PC for adb access, Recovery can read the keys from /data.（不太理解……不过用错不大。略
）
Speed is similar to Lollipop; except that Lollipop runs the CPU at 1.4GHz and Marshmallow at 1.0GHz. If you want more speed but less battery, use an app like 'No-frills CPU control' to run at 1.4GHz. Don't forget to check 'set at boot' or it will revert to 1.0 at next boot.
Note that the CPU is designed for 1.4GHz; SonyEricsson chose to underclock to 1.0 to conserve battery.（系统速度上是相似的，除了Lollipop的cpu频率是1.4G而Marshmallow的是1.0G）
Bluetooth works, or it doesn't, or it does when it feels like it; this is a known problem.（蓝牙工不工作要看他的心情，这个原因已经找到只是还未修复）
The screen may be a bit dark; some prefer to disable Settings > Display & Lights > Adaptive brightness（屏幕亮度可能有点暗，自己去设置里面调一下好了）
Keyboard swiping ('Gesture Typing') does not work (maybe because of missing dictionary files). Easy workaround is to install Google Keyboard from the Play store.（自带键盘的问题，咱们一般都用自己安装的第三方的）
In Recovery mode, initially any adb command other than sideload results in "unauthorized". Once you have booted and authorized the PC for adb access, Recovery can read the keys from /data.（不太理解……不过用错不大。略
）Speed is similar to Lollipop; except that Lollipop runs the CPU at 1.4GHz and Marshmallow at 1.0GHz. If you want more speed but less battery, use an app like 'No-frills CPU control' to run at 1.4GHz. Don't forget to check 'set at boot' or it will revert to 1.0 at next boot.
Note that the CPU is designed for 1.4GHz; SonyEricsson chose to underclock to 1.0 to conserve battery.（系统速度上是相似的，除了Lollipop的cpu频率是1.4G而Marshmallow的是1.0G）
Bluetooth works, or it doesn't, or it does when it feels like it; this is a known problem.（蓝牙工不工作要看他的心情
，这个原因已经找到只是还未修复）The screen may be a bit dark; some prefer to disable Settings > Display & Lights > Adaptive brightness（屏幕亮度可能有点暗，自己去设置里面调一下好了）
Keyboard swiping ('Gesture Typing') does not work (maybe because of missing dictionary files). Easy workaround is to install Google Keyboard from the Play store.（自带键盘的问题，咱们一般都用自己安装的第三方的）
不感兴趣
开通SVIP免广告
者
不感兴趣
开通SVIP免广告
